UPDATED: July 25, 2017

The waste and overflow is the drain mechanism behind and under the bathtub that connects the overflow with the tub drain. It’s usually covered with a chrome plated cover above the tub drain near the top of the tub level. It allows water to drain out of the tub in the event the water is left on or the level gets too high when someone gets in and the water is displaced. Usually, the complete repair of the waste and overflow is time-consuming and difficult. As you can see there is no easy way to get to the drain unless you have a point of access in a wall behind the drain or from underneath the tub. We’ve got the best method for you, so let’s jump right into these step-by-step instructions.

Installing a Tub Drain and Over Flow.

When a waste and overflow needs to be repaired the plumbing technician needs to get access either underneath the tub or more preferably behind the tub. If this is a waste problem, locate the hair or loose odds and ends that is causing the clog and remove it. If you’re the drain remover, you’re definitely going to want to keep your eyes peeled for the next few steps.

The first step to removing the waste and overflow is to remove the overflow cover. The removal of the cover is an easier part of the process. This overflow cover is usually directly above the plug that drains the water on the bottom of the tub. You usually don’t need a tool to do this. The second and much more difficult step is to unscrew the tub drain from the shoe. The tub drain threads into the drain shoe body of the waste and overflow and snugs up both to the bathtub.

When you remove the drain stopper most times there are crossbars that the stopper is attached to, these are used to back the drain out. You also might run into a drain flange which is the finished and visible part around your drain hole. The drain flange helps seals the tub and drain assembly.

Quite often the drain breaks, making this job a time consuming project. (We will expand upon removing and replacing a waste and overflow). Here is another place where this can become difficult. If you’ve got access to the drain from behind the tub there is usually a slip nut that connects the drain to the drainage piping, this is a fairly easy installation, if not it is very difficult to remove the drain from below. Most times you have to cut it out and piece it back together. It is not unusual for a waste and over repair to take 6 hours or so.

Bathtub Overflow Drain Cover

The drain cover’s finish is the most apparent reason for changing it. The finish tends to pit or peel. The waste and overflow cover usually has one screw in the middle or two to secure the cover to the body of the waste.

The Problem is Behind the Faceplate and Water Leaks down the Drainwaste and overflow Waste Tube.

The single biggest reason a waste and overflow leaks is the gasket behind the drain cover or faceplate. The rubber behind the tub begins to break down and when the water level rises to the level of the overflow the water makes it’s way to any breach in the seal. Sometimes these leaks can be tricky to find because the water may run down the drain waste tube and the leak shows itself right at the spot of the waste and overflow or the water can run along and under the tub and shows itself quite a distance away from the actual leak.

How do I Fix the Tub Gasket and Stop the Plumbing from Leaking?

Honestly, we’ve always said that we would be cautious when plugging a product. However, when one comes along that is innovative and can save people time and money it’s our duty to let people know.

There is an Easy and Economical Way to Repair Your Bathtub Waste and Overflow?

The Watco Universal NuFit® is a quick and easy way to freshen up your tub drain and the Ultimate Overflow Gasket takes care of the issues of any leaking you may have from the overflow gasket. The Ultimate Overflow kit uses a patented gasket that fits on the outside of the tub and telescopes into the overflow tube bypassing the damaged gasket eliminating the leaks. Another common issue with bathtubs, in general, is the drain. Chances are if the waste and overflow gasket and cover are damaged the bathtub drain looks the same.

The Watco Universal NuFit® drain kit features an all brass lift and turn remodel drain that fits on top and into your old drain. No need to attempt to unscrew the old drain and risk possible damage to the tub or drain assembly. Just unscrew and remove the old lift and turn assembly and or linkage pop-up drain. Clean with a mild detergent removing any soap or build-up, dry thoroughly, apply the kits RTV silicone bond caulk, place the drain on top of the old, press, turn and leave for 24 hours and you’re done. The entire drain remodel can be done in 15 minutes.

Not Just for Repairs

The great thing about this product is it’s not just for repairs. If you are remodeling your bath or changing the finishes on your faucets you can purchase the kit in all of the currently popular finishes. You don’t have to live with a chrome or brass waste and overflow cover/drain with new brushed nickel faucets. Both kits come in a variety of finishes including chrome, brushed nickel, stainless steel and oil rubbed bronze. The Watco drain is available in many other colors as well.

Related Posts Plugin for WordPress, Blogger...